Reecote EC017 A/S - Anti Static Floor Paint

Vendor: Virtus Resins
Reecote EC017 A/S is designed for use in areas where a build up of static may cause a problem for equipment or people. It is suitable for use where a...

Available

With VAT: £99.60 | Without VAT:
£83.00
Size
Color
Beige
Yellow
Holly Green
Leaf Green
Irish Green
Carnival Red
Tile Red
Blue Grey
Flint Grey
Squirrel Grey
Goosewing Grey
Light Grey
Tartan Blue
Cornflower Blue
Pigeon Blue
White
Black
Coverage Calculator
Calculate

    Reecote EC017 A/S is designed for use in areas where a build up of static may cause a problem for equipment or people. It is suitable for use where a hard wearing hygienic, anti static floor paint is required.

    Suitable Surfaces

    Concrete and steel.

    Advantages

    • Anti static epoxy floor coating
    • Low Odour
    • Hygienic and Easy Clean Finish
    • Good Chemical Resistance
    • Wide Colour Range
    • Can be made anti slip by using Virtus anti slip aggregate
    • Will not support bacterial growth.
    • Can be made decorative with the addition of Virtus PVA Flakes scattered into the wet resin, once dry, sand down any protruding or Flake edges and seal with Reecote ECO17 Anti-static Clear.

    Usage

    Indoor (some colour change would occur if used outdoors).

    Cleaning

    Hot water jet washing with detergents and scrubber driers.

    Thickness

    Approx 0.5mm. Can be built up to a maximum of 1 mm from the application of multiple coats.

    Primer

    Must be used with Reeprime CPS900.

    Coverage

    Each 6kg of Reecote EC017 AS will cover approximately 20m².

    Coats Required

    One coat of Reeprime CPS900 primer followed by two coats of Reecote EC017 AS.

    Pot Life

    30 Minutes (at 20ºC)

    Waiting time between coats: Min 12hrs and Max 24hrs (at 20ºC)

    Curing Times

    • Foot traffic - 16hrs - 1 day
    • Lightly serviceable - 2 days
    • Fully serviceable - 7 days

    Surface Preparation:

    Dry > 50. Method BS7976 pt1-3 2002

    New concrete should have an RH% of 75% or less.

    The substrate should be clean, free from laitance, oil, grease or other agents, which may impair adhesion. Cleaning techniques may include acid etching, grinding, light mechanical scabbling, blasting or degreasing, depending on wall contamination.

    Existing concrete walls should be sound and free from loose material. Damaged areas should be repaired with a Reepare Mortar prior to the coating application.

    Mixing Instructions:

    IT IS IMPERATIVE THAT THE MIXING IS CARRIED OUT IN THE RESIN CONTAINER.

    Reecote EC017 A/S is a two pack system and it is very important to ensure the curing agent, compound B, should be added to the entire contents of the resin pack, component A and stirred thoroughly until uniform colour is achieved (2-3 minutes).

    Packs should not be split unless accurate weighing facilities are available. Reecote EC017 A/S is supplied in pre-weighed units of the correct proportions.

    Application:

    Reecote EC017 A/S should be applied to Reeprime CPS900 (see separate data sheet). Apply the mixed material to the suitably prepared floor by brush or roller; ensure complete coverage of the floor area. Apply the second coat within 24 hours of the first.

    Certain colours can be made to order subject to availability.

    BEIGE YELLOW HOLLY GREEN LEAF GREEN
    ELFIN GREEN CARNIVAL RED TILE RED STORM GREY
    FLINT GREY GOOSEWING GREY LIGHT GREY TARTAN BLUE
    CORNFLOWER BLUE PIGEON BLUE WHITE BLACK

    Technical Datasheets

    Reecote ECO17 A/S

    data sheet download


    Safety Data Sheets


    Reecote EC017 Hardener

    data sheet download

    Reecote EC017 Resin

    data sheet download

    Related Product

    Best Sellers

    Suppliers & Partners