Reeflor EL005 - Self Smoothing Epoxy Floor Topping

Vendor: Virtus Resins
Reeflor EL005 is suitable for use where a hard wearing; dust free; hygienic, easy clean floor topping is required. Ideal situations include industrial or commercial floors, laboratories, showrooms, schools, plant...

Available

With VAT: £146.40 | Without VAT:
£122.00
Size
Color
Beige
Yellow
Holly Green
Leaf Green
Irish Green
Carnival Red
Tile Red
Blue Grey
Flint Grey
Squirrel Grey
Goosewing Grey
Light Grey
Tartan Blue
Cornflower blue
Pigeon Blue
White
Black

Reeflor EL005 is suitable for use where a hard wearing; dust free; hygienic, easy clean floor topping is required. Ideal situations include industrial or commercial floors, laboratories, showrooms, schools, plant rooms etc

Reeflor EL005 is based on a blend of epoxy resins, curing agents and selected fine aggregates. The easily mixed system provides a 4mm (minimum) floor topping with advantages to both contractors and clients. All resins, curing agents and aggregates are supplied pre-weighed and blended ready for use on site.

Advantages

  • Self Smoothing
  • Easy to Clean
  • Hygienic
  • Good Chemical Resistance
  • Solvent Free
  • Wide Colour Range
  • Hard Wearing

Coverage

3.86 m² @4mm per pack.

Curing Schedule

Drying time for foot traffic is 1 day, lightly serviceable is 2 days and fully serviceable is 7 days.

Priming

All floors must be thoroughly sealed with Reeprime EP800 prior the application of Reeflor EL005.

Surface Preparation

New concrete should have an RH% of 75% or less. The substrate should be clean, free from laitence, oil, grease or other agents, which may impair adhesion. Cleaning techniques may include acid etching, grinding, light mechanical scabbling, blasting or degreasing, depending on contamination.

Existing concrete floors should be sound and free from loose material. Damaged areas should be repaired with a Reepare Mortar prior to the coating application.

Cementitious substrates should be sound and of sufficient compressive strength (min. 25 N/mm²) and a minimum pull off strength off 1.5 N/N/mm².

Priming:

All floors must be thoroughly sealed with Reeprime EP800. Depending on the porosity of the substrate a second coat may be required. Reeprime must be tack-free before the application of Reeflor EL005.

Expansion Joints:

All existing joints in the substrate should be followed through into the Reeflor EL005.

Mixing & Application

The entire contents component B should be added to the entire contents of component A, and should be mixed together using a low speed electric stirrer (300-400 RPM) for a minimum of 3 minutes until a uniform mix has been achieved. Transfer to suitable sized mixing bucket scraping well the sides of the container. Gradually add aggregate component C while mixing. Continue mixing for 2 minutes or until a uniform mix has been achieved. Pour the mixed material onto the pre-sealed substrate and spread to the required level by steel trowel. Roll immediately in two directions with a spiked roller.

Application Technique

Pour the mixed material onto the pre-sealed substrate and spread to the required level by steel trowel aided by a spiked roller. Spike rolling should be effected within 5-10 minutes of application in order to avoid interfering with flow.

Certain colours can be made to order subject to availability.

BEIGE YELLOW HOLLY GREEN LEAF GREEN
ELFIN GREEN CARNIVAL RED TILE RED STORM GREY
FLINT GREY GOOSEWING GREY LIGHT GREY TARTAN BLUE
CORNFLOWER BLUE PIGEON BLUE WHITE BLACK

Technical Datasheets

EL005 Datasheet

data sheet download


Safety Data Sheets


EL005 Hardener

data sheet download

EL005 Resin

data sheet download

Related Product

Best Sellers

Suppliers & Partners