Reeflor EL1001 - Self-Smoothing Epoxy Topping

Vendor: Virtus Resins
Reflor EL1001 is 3-part self-smoothing epoxy topping which is typically installed from 1mm thickness. Typical Installations Reeflor EL1001 is suitable for use where a hard wearing, dust free, hygienic, easy to...

Available

With VAT: £168.00 | Without VAT:
£140.00
Size
Color
Beige
Yellow
Holly Green
Leaf Green
Irish Green
Carnival Red
Tile Red
Blue Grey
Flint Grey
Squirrel Grey
Goosewing Grey
Light Grey
Tartan Blue
Cornflower Blue
Pigeon Blue
White
Black
Coverage Calculator
Calculate

    Reflor EL1001 is 3-part self-smoothing epoxy topping which is typically installed from 1mm thickness.

    Typical Installations

    Reeflor EL1001 is suitable for use where a hard wearing, dust free, hygienic, easy to clean floor topping is required. Ideal situations include industrial or commercial floors, laboratories, car showrooms, gangways etc.

    Reeflor EL1001 is based on a blend of epoxy resins, curing agents and selected fine minerals. The easily mixed system provides a 1mm (minimum) floor topping with advantages to both contractors and clients. All resins component A, and curing agents, component B, are supplied pre-weighed and ready for use on site

    Advantages

    • Self Smoothing
    • Hygienic
    • Good Chemical Resistance
    • Solvent Free
    • Wide Colour Range
    • Hard Wearing

    Priming

    All floors must be thoroughly sealed with Reeprime EP550 or Reeprime EP800 prior to the application of Reeflor EL1001.

    Coverage

    1.7 kg / m²  minimum. 20 kg pack will cover up to 11.76 m² @ 1mm thick.

    Curing Schedule

    Drying times for foot traffic is 1 day, for lighty serviceable traffic is 2 days and fully serviceable is 7 days.

    Priming:

    All floors must be thoroughly sealed with Reeprime EP550, RBS80, or Reeprime EP800 prior to the application of Reeflor EL1001.

    Depending on the porosity of the substrate a second coat may be required. Reeprime must be tack free before the application of Reeflor EL1001.

    Surface Preparation

    New concrete should have an RH% of 75% or less. The substrate should be clean, free from laitence, oil, grease or other agents which may impair adhesion. Cleaning techniques may include acid etching, grinding, light mechanical scabbling, blasting or degreasing, depending on floor contamination. Existing concrete floors should be sound and free from loose material. Damaged areas should be repaired with a Reepare Mortar prior to application.

    We recommend that all floors suitable for Reeflor EL1001 should be inspected prior to application where full and further recommendations will be given.

    Storage, Mixing & Application:

    IT IS IMPERATIVE THAT THE MIXING IS CARRIED OUT IN THE RESIN CONTAINER.

    Reeflor EL1001 is supplied in pre-weighed packs and no addition of solvents or aggregates should be carried out on site. The entire contents of the curing agent, component B, should be added to the entire contents of the resin pack, component A, and should be mixed together using a low speed electric stirrer (300-400 rmp) for a minimum of 3 minutes until a uniform mix has been achieved. Transfer to another container of the same capacity, scraping well the container sides and mix for a short period. This will eliminate possible soft spots on the applied system. Packs should not be split.

    Pour the mixed material onto the pre-sealed substrate and spread to the required level by steel trowel. Roll immediately in two directions with a spiked roller.

    Joining:

    Joining time should not exceed 35 minutes at temperatures of 18-20ºC and 45 minutes at temperatures of 12-18ºC. Disturbances to the applied materials outside these timings may create streaking and discoloration at the joining point.

    Expansion Joints

    All existing joints in the substrate should be followed through into the Reeflor EL1001.

    Certain colours can be made to order subject to availability.

    BEIGE YELLOW HOLLY GREEN LEAF GREEN
    ELFIN GREEN CARNIVAL RED TILE RED STORM GREY
    FLINT GREY GOOSEWING GREY LIGHT GREY TARTAN BLUE
    CORNFLOWER BLUE PIGEON BLUE WHITE BLACK

    Technical Datasheets

    Reeflor EL1001

    data sheet download

    Safety Data Sheets


    Reeflor EL1001 Component A

    data sheet download

    Reeflor EL1001 Component B

    data sheet download

    Related Product

    Best Sellers

    Suppliers & Partners