Flowthane 500 UVR (Previously Flexicoat UV Resistant) - High Build Flexible Polyurethane Coating
Vendor: Virtus Resins
Flowthane 500 UVR is a flexible high build polyurethane floor coating with excellent abrasion and impact resistance and provides a medium duty coating for floors. Two coats of Flowthane 500 UVRprovide a build equivalent to almost 10 coats of conventional solvent containing coatings.
Flowthane 500 UVR is ideal for areas requiring good wear resistance combined with economical cost such as: storage areas, plant rooms, warehousing, toilets etc. Also suitable for lining chemical bunds due to its chemical-resistant properties.
Flowthane 500 UVR is a FeRFA Type 3, high-build medium-duty flooring system able to withstand regular foot traffic and frequent fork lift truck traffic.
Typical Installations
Flowthane 500 UVR is suitable for the protection of concrete floors subject to medium duty traffic (regular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys). As it is flexible, it is ideal for use on floors which experience some minor movement such as floors holding vibrating machinery or mezzanines. Typical uses include areas requiring good wear resistance combined with economical cost such as: storage areas, plant rooms, warehousing, toilets etc. Also suitable for lining chemical bunds due to its chemical-resistant properties.
Appearance
A medium gloss surface with a slightly stippled finish.
Suitable Substrates
Flowthane 500 UVR can be applied to concrete, polymer modified cementitious screeds, steel, timber and asphalt.
Thickness
0.25 - 1 mm depending on application rate and number of coats.
Coverage
5 kg will cover 8m² (2 coats). It can be applied as a one coat application at a coverage rate of 0.365g per m² or over (the aesthetics are dependant on application technique and substrate quality).
Application Conditions:
The ideal ambient, substrate and material temperature range is 15 - 25 ºC. Localised heating or cooling equipment may be required outside this range otherwise the surface finish and application viscosity may be impaired. The maximum substrate and atmospheric relative humidity should be 75%. The substrate and uncured floor must be kept at least 3 ºC above the dew point to reduce the risk of condensation or blooming on the surface, from before priming to at least 48 hours after application.
Surface Preparation:
Inadequate preparation will lead to loss of adhesion and failure. In coatings, there is a tendency for the finish to mirror imperfections in the substrate. For concrete substrates, grinding or light vacuum contained shot-blasting is therefore preferred over planing for these systems. Refer to the Virtus Guide to Surface Preparation.
Priming:
Flexicoat UVR does not normally require a primer on dry substrates. When treating extremely porous or damp concrete, prime as follows: Substrate relative humidity <75%: Flowdur Primer Substrate relative humidity >75%: Flowprime DPM
Mixing & Application:
Prior to mixing, the temperature of both components must be between 15 and 25 ºC. Add the hardener component to the coloured resin component and mix using a low speed electric mixer (300 - 400 rpm) for at least 3 minutes until homogeneous. Keep the mixing paddle fully submerged to avoid the entrapment of air and scrape the sides and bottom of the vessel several times. Decant the mixed material to a second mixing vessel and mix as above for a further minute. Apply with a medium roller directly from a paint tray. Push the resin well into the surface making sure the floor is fully wetted and then pull back lightly with the roller to the required thickness.
For a 1 coat application we recommend that a rubber lipped squeegee is used followed by a short nap roller. This may produce a slight orange peel effect across the surface.
Important: Both liquids are pre-weighed and designed to be mixed together in their entirety. It is essential that the full amounts are mixed together and until homogeneous to ensure the product cures correctly and to the desired finish.
Certain colours are subject to availability
| BLACK | CHARCOAL | MID GREY | DARK GREY |
| LIGHT GREEN | GREEN | CHELSEA BLUE | MIDNIGHT BLUE |
| LIGHT GREY | PLATINUM | STEEL | SLATE |
| SAFETY RED | TILE RED | SAHARA | YELLOW |
| LIGHT BLUE | MID BLUE | SAFETY YELLOW | BUFF |
| WHITE |
Flexicoat UVR
Safety Data Sheets
Flexicoat UVR Hardener
Flexicoat UVR Resin
Related Product
Best Sellers
