Easycoat - Epoxy Floor Paint

Vendor: Virtus Resins
Easycoat is our high build, easy to apply epoxy floor paint. It is a two pack, solvent free, hard wearing and is available in a range of attractive colours. It...

Available

With VAT: £102.00 | Without VAT:
£85.00
Size
Color
Black
Charcoal
Dark Grey
Mid Grey
Slate
Light Grey
Platinum
Steel
Light Green
Green
Midnight Blue
Chelsea Blue
Mid Blue
Light Blue
Safety Red
Tile Red
Sahara
Yellow
Safety Yellow
Buff
White
Coverage Calculator
Calculate

    Easycoat is our high build, easy to apply epoxy floor paint. It is a two pack, solvent free, hard wearing and is available in a range of attractive colours. It is designed to give excellent abrasion and chemical resistance. It is a thick resin and can be applied up to 1mm thick. Even on rough and uneven concrete, Easycoat cures to a smooth, gloss / slightly silky, easily cleanable surface finish, capable of withstanding the toughest of factory conditions.

    Suitable Surfaces

    Concrete, Grano and Steel.

    Typical Installations

    • Floors in processing and manufacturing plants.
    • Frequent fork lift truck traffic areas
    • Factories and warehousing
    • Commercial garages, vehicle repair and maintenance depots
    • Aircraft hangers
    • Food preparation and storage areas

    Easycoat is used in areas where a good wearing and chemical resistant surface is required, such as chemical plant storage areas, laboratories, breweries and general vehicle repair garages.

    Advantages

    • Can withstand tough industrial conditions
    • Easy to apply
    • Gives a hygienic, seamless floor finish which is easy to clean
    • Low odour
    • Solvent free
    • Will not support bacterial growth.
    • Can be made decorative with the addition of Virtus PVA Flakes scattered into the wet resin, once dry, sand down any protruding or Flake edges and seal with Easycoat Clear.
    • Can be made anti slip with the addition of Virtus Anti-slip Aggregate scattered into the first coat of wet resin.

    Primer 

    Easycoat does not normally require a primer. On very weak or porous concrete, it is advisable to prime with Flowprime SF.

    Surface Preparation

    Surfaces to be treated must be sound free from oil or other contaminants, flaky paints, laitance and dust. Smooth and dense surfaces must be mechanically abraded to provide a key and all dust

    Coverage 

    5 kg pack will  cover up to 20 square metres in a single coat (2 coats recommended).

    Curing Schedule @ 20 ºC

    • Working life of full packs - 30 minutes
    • Over-coating time (minimum) - 16 -24 hours
    • Light foot traffic - 24 hours
    • Medium duty traffic - 48 -72 hours
    • Full Cure -7 days

    Cleaning & Maintenance

    Hot water jet washing, detergents, scrubber dryers.

      Priming

      Easycoat does not normally require the use of a primer. When treating extremely weak or porous concrete it is advisable to prime with Flowprime SF.

      Mixing

      Pre-mix the coloured resin component before use. Add the hardener component to the coloured resin component and mix using a low speed electric mixer (200 - 500 rpm) fitted with a mixing paddle designed to minimize air entrainment for 3 minutes until homogeneous. Care should be taken to ensure that any material adhering to the sides and bottom of the mixing vessel is thoroughly mixed in otherwise uncured patches may result.

      Important: Both liquids are pre-weighed and designed to be mixed together in their entirety. It is essential that the full amounts are mixed together and until homogenous to ensure the product cures correctly and to the desired finish.

      Application

      Apply by brush or medium pile roller from a paint tray or scuttle avoiding pooling of the coating. Pull back to a tight coat observing the coverage rates. A wet film thickness wheel should be used to check application thickness. Do not apply subsequent coats until the previous coat is completely dry. This will depend on temperature and degree of ventilation. Adequate ventilation and air movement is necessary. Each coat should be applied at right angles to the previous coat in order to minimize imperfections and unevenness overall. Uneven application may lead to differences in shade across the cured floor highlighted by the gloss finish. Gloss levels may vary where substrate porosity is high.

      Certain colours are subject to availability

      BLACK CHARCOAL MID GREY DARK GREY
      LIGHT GREEN GREEN CHELSEA BLUE MIDNIGHT BLUE
      LIGHT GREY PLATINUM STEEL SLATE
      SAFETY RED TILE RED SAHARA YELLOW
      LIGHT BLUE SAFETY YELLOW BUFF WHITE
      MID BLUE

      Easycoat Technical Data Sheet

      data sheet download


      Safety Data Sheets


      Easycoat Hardener

      data sheet download

      Easycoat Resin

      data sheet download

      Related Product

      Best Sellers

      Suppliers & Partners