Flexideck UVR - Car Park Decking Coating

Vendor: Virtus Resins
Flexideck UVR is a flexible high build polyurethane floor coating with excellent  abrasion and impact resistance which provides heavy duty coating for floors and decks. Two coats of Flexideck UVR...

Available

With VAT: £108.00 | Without VAT:
£90.00
Size
Color
Black
Charcoal
Dark Grey
Mid Grey
Light Grey
Slate
Steel
Platinum
Midnight Blue
Chelsea Blue
Mid Blue
Light Blue
Sahara
Yellow
Safety Yellow
Buff
Light Green
Green
Safety Red
Tile Red

Flexideck UVR is a flexible high build polyurethane floor coating with excellent  abrasion and impact resistance which provides heavy duty coating for floors and decks. Two coats of Flexideck UVR provide a build equivalent to almost 10 coats of conventional solvent containing coatings. Flexideck can be applied as a one coat application at a coverage rate of 0.365g per m² or over (the aesthetics are dependant on application technique and substrate quality).

Typical Installations

Can be used externally and internally.

Primarily used as a sealcoat for broadcast systems such as Intermediate or Top Car Park Decks (due to its weatherproofing qualities). Typical uses also include  areas requiring good wear resistance combined with economical cost such as: storage areas, plant rooms, warehousing, toilets etc. Also suitable for lining chemical bunds due to its chemical-resistant properties.

Advantages

  • Coloured polyurethane coating
  • Excellent wear resistance
  • Lightly stippled gloss finish
  • Suitable for external applications
  • Anti-scratch
  • UV-stable
  • Chemical resistant
  • Can be made anti-slip by the addition of aggregate to the first coat of wet resin (scatter or full blind)

Colours

Flexideck UVR is available in a range of standard colours (please see Colour Chart).

Appearance

A medium gloss surface in a range of colours with a slightly stippled finish.

Suitable Substrates

Flexideck UVR can be applied to concrete, polymer modified cementitious screeds, steel, timber and asphalt.

Pack Size

5 and 10 kg units.

Thickness

0.5 mm - 1 mm (depending on the number of coats used)

Coverage

A 5 kg pack will cover 8m² (2 coats). Consumption rates will be increased when over-coating aggregated / non-slip systems.

Surface Preparation

Inadequate preparation will lead to loss of adhesion and failure. In coatings, there is a tendency for the finish to mirror imperfections in the substrate. For concrete substrates, grinding or light vacuum contained shotblasting is therefore preferred over planing for these systems.

Components

Each unit of Flexideck UVR comprises of: one part Resin and one part Hardener. Both components are pre-weighed and ready to mix.

Application Conditions:

The ideal ambient, substrate and material temperature range is 15 - 25 ºC. Localised heating or cooling equipment may be required outside this range otherwise the surface finish and application viscosity may be impaired. The maximum substrate and atmospheric relative humidity should be 75%. The substrate and uncured floor must be kept at least 3 ºC above the dew point to reduce the risk of condensation or blooming on the surface, from before priming to at least 48 hours after application.

Surface Preparation:

Inadequate preparation will lead to loss of adhesion and failure. In coatings, there is a tendency for the finish to mirror imperfections in the substrate. For concrete substrates, grinding or light vacuum contained shot-blasting is therefore preferred over planing for these systems. Refer to the Virtus Guide to Surface Preparation.

Priming:

Flexicoat UVR does not normally require a primer on dry substrates. When treating extremely porous or damp concrete, prime as follows:

Substrate relative humidity <75%: Flowdur Primer

Substrate relative humidity >75%: Flowprime DPM

Mixing & Application:

Prior to mixing, the temperature of both components must be between 15 and 25 ºC.

Add the hardener component to the coloured resin component and mix using a low speed electric mixer (300 - 400 rpm) for at least 3 minutes until homogeneous. Keep the mixing paddle fully submerged to avoid the entrapment of air and scrape the sides and bottom of the vessel several times. Decant the mixed material to a second mixing vessel and mix as above for a further minute. Apply with a medium roller directly from a paint tray. Push the resin well into the surface making sure the floor is fully wetted and then pull back lightly with the roller to the required thickness.

For a 1 coat application we recommend that a rubber lipped squeegee is used followed by a short nap roller. This may produce a slight orange peel effect across the surface.

Important: Both liquids are pre-weighed and designed to be mixed together in their entirety. It is essential that the full amounts are mixed together and until homogeneous to ensure the product cures correctly and to the desired finish.

Certain colours are subject to availability


BLACK CHARCOAL MID GREY DARK GREY
LIGHT GREEN GREEN CHELSEA BLUE MIDNIGHT BLUE
LIGHT GREY PLATINUM STEEL SLATE
SAFETY RED TILE RED SAHARA YELLOW
LIGHT BLUE MID BLUE SAFETY YELLOW BUFF
WHITE

Flexideck UVR

data sheet download


Safety Data Sheets


Flexdeck UVR Hardener

data sheet download

Flexideck UVR Resin

data sheet download

Related Product

Best Sellers

Suppliers & Partners